Products

AEM's Universal High Flow -10 AN Inline Filter is specifically engineered for maximizing flow without sacrificing filtration, and is designed for ease of installation. The end caps are machined with -10AN female fittings that allow the filter to flow up to 12.32 gpm @...

Any enthusiast running boost, nitrous or high RPMs is aware of the trade-offs associated with inductive coils versus converting to a capacitive-type discharge ignition system (CDI). While inductive coils deliver a long spark duration, they lack enough energy to light off the combustion chamber...

Auto enthusiasts who have forced induction engines, high RPM engines or run nitrous oxide are aware of the compromises that come with using inductive coils instead of converting to a Capacitive Discharge Ignition system (CDI). While inductive coils deliver a long spark duration with...

-10AN Universal High Flow Fuel Filter Replacement for Part #25-201BK

AEM's stainless-steel tall wideband UEGO sensor bungs are designed specifically for use on forced induction applications using the 4-Channel Wideband UEGO Controller, but can be used for wideband sensors on any vehicle and with any AEM wideband UEGO AFR controller. The tall design of...

These AEM LSU 4.2 sensors have a laser-etched, calibrated resistor in the sensor's connector body. This resistor is specifically created for the exact sensor that it is attached to. Modifying this will invalidate the sensor's output. The wideband sensor is laboratory-calibrated at the Bosch...

V2 Water/Methanol Injection 5 Gallon Tank Kit with Conductive Fluid Level Sensor

The AEM Water/Methanol injection for forced induction (turbocharged or supercharged) Gas & Turbo Diesel applications is a proven means for effectively reducing engine inlet air temperatures and enhancing combustion efficiency whilst suppressing harmful detonation. This allows for reliable increase in boost and advance timing...

Water/methanol injection for forced induction (turbocharged or supercharged) gas-powered race engines is a proven means for effectively reducing engine inlet air temperatures and suppressing harmful detonation. This allows racers to reliably increase boost and advance ignition timing-without using high-octane racing fuel-for power gains of...

V2 Water/Methanol HD Controller Kit - Internal MAP with 40psi max, CONTROLLER ONLY

V2 Water/Methanol Multi Input Controller Kit- 0-5v/MAF Frequency or Voltage/Duty Cycle/Ext MAP, CONTROLLER ONLY

The new controller designs feature large, turn-resistant knobs and larger numbering to easily set accurate start and full activation points, with covered status LED and test buttons for added splash resistance. A plug is integrated into the controller housing for mating to the redesigned...

These new controllers retain the "Boost Safe" injection failsafe system, which is an output that will activate if there is a short, loss of continuity or high or low voltage or low fluid condition, allowing users to define their failsafe strategy from something as...

Boost Dependent and Multi-Input (0-5v/frequency) progressive controller designs feature large adjustment knobs, integrated plug for harness connection, integrated fuse, covered status light and test button for enhanced splash resistance and mounting tabs Wiring harness is terminated with a positive-lock connector on one end with...

The new controller designs feature large, turn-resistant knobs and larger numbering to easily set accurate start and full activation points, with covered status LED and test buttons for added splash resistance. A plug is integrated into the controller housing for mating to the redesigned...

Our breakthrough injector design uses unique Swirl Generator Technology that improves atomization to deliver faster inlet temp cooling and uses less fluid to maintain inlet air cooling. We include three Swirl Generators that deliver 250cc, 500cc, and 1000cc of flow.

Racers with high compression naturally aspirated engines or boosted engines who are looking for an alternative to boost-dependent water/methanol injection controllers have a solution in AEM's Multi-Input WMI controller. The multiple input design enables users to install AEM's Water/Methanol Injection Kit on both high...

Water/methanol injection for forced induction (turbocharged or supercharged) gas-powered race engines is a proven means for effectively reducing engine inlet air temperatures and suppressing harmful detonation. This allows racers to reliably increase boost and advance ignition timing-without using high-octane racing fuel-for power gains of...

Replacement V3 Water/Methanol Injectors (Qty 2), Includes Interchangeable Swirl Generators for 250cc, 500cc, & 1000cc of flow for each injector

If part of your existing AEM Water/Methanol Injection system has become damaged, we offer all of the component parts individually, including our 200 PSI water/methanol injection pump, a WMI check valve kit, water/methanol injection tubing, 1.15- and five-gallon water/methanol fluid tanks and our conductive...